JBUDS AIR
EARBUDS
AUTO-CONNECTING EARBUDS
Press and hold both buttons 3+ seconds to power ON.
The Left earbud turns solid white and Right earbud blinks blue/white indicating ready to pair to your device.
ADDING NEW / ADDITIONAL BLUETOOTH DEVICES:
Turn OFF Bluetooth from any previously connected device. Turn ON Bluetooth from new device. Take earbuds out of the case.
Earbuds will automatically enter Bluetooth Pairing. Select “JLab JBuds Air” in new device settings to connect.
FIRST TIME SETUP
1
CONNECTING TO BLUETOOTH
Select “JLab JBuds Air” in your device settings.
Voice prompt “Bluetooth connected” followed by solid white lights will indicate you are connected.
2
Press and hold
3+ seconds
Left
Right
Bluetooth
Settings
JLab JBuds Air
C
U
S
T
O
M
E
R
S
U
P
P
O
R
T
U
.
S
.
B
A
S
E
D
We love that you are rocking JLab Audio!
We take pride in our products and fully stand behind them.
YOUR WARRANTY
All warranty claims are subject to JLab Audio
authorization and at our sole discretion. Retain your
proof of purchase to ensure warranty coverage.
CONTACT US
Reach out to us at [email protected]
or visit jlabaudio.com/contact
L
I
M
I
T
E
D
T
W
O
Y
E
A
R
REGISTER TODAY
jlabaudio.com/register
Product updates | How-to tips
FAQs & more
Match the corresponding L and R
letters on the charging case for
proper charging. The earbuds
will auto power OFF and start
charging.
Blue lights will indicate earbuds
are charging and will turn OFF
when fully charged.
Earbuds will auto power ON and reconnect
to your device when taken out of the case.
RIGHT
EARBUD
LEFT
EARBUD
LEFT
EARBUD
RIGHT
EARBUD
VOLUME DOWN: Single press
SIRI (iOS) or “OK GOOGLE”
(ANDROID): Double press
TRACK BACK: Press & hold 1+ sec
TURN ON: Press & hold 2+ sec
TURN OFF: Press & hold 5+ sec
CHANGE EQ: Triple press
VOLUME UP: Single press
ANSWER: Single press
HANGUP: Double press
REJECT INCOMING CALLS:
Press & hold 1+ sec
PLAY / PAUSE: Double press
TRACK FORWARD: Press & hold 1+ sec
TURN ON: Press & hold 2+ sec
TURN OFF: Press & hold 5+ sec
CHANGE EQ: Triple press
VOICE PROMPTS
“Hello”: Power ON
“Earbuds joined”:
Earbuds paired to each other
“Ready to Pair”: JBuds Air are
ready to pair to Bluetooth device
“Bluetooth Connected”:
Earbud is connected to device
“Battery Full”: 100-80%
“Battery Medium”: 80-20%
“Low Battery”: Less than 20%
When power decreases to 10%,
“Low Battery” will play
“Goodbye”: Power OFF
BUTTON FUNCTIONS
Click either the right or left earbud 3 times for different EQ settings (JBuds Air will cycle 3 EQ settings).
CUSTOM EQ
3
SOUND MODES
JLab SIGNATURE
JLab C3™ signature
sound with amplified
bass and vocals
BALANCED
Even sound with
no additional
enhancements
BASS BOOST
Amplified bass
and sub-bass
CHARGING EARBUDS
Connect the JBuds Air to computer
or USB 5V 1A (or less) output device.
LEDs pulse white when charging and
turn solid white when fully charged.
OR
CHARGING CASE
1 2
TROUBLESHOOTING
FITTING
Instructional videos at: JLABAUDIO.COM/MANUALS
ECHOES ON CALLS
If you experience microphone echo/call quality with the JBuds Air, make sure the Cush Fin is not blocking the microphone port.
Microphone open
Microphone covered
Try all the optional Cush Fins and
ear tips for best fit and proper seal.
The Cush Fin should be aligned by
positioning the contour around the
microphone hole.
Cush Fin™
Ear tip
TROUBLESHOOTING
NO AUDIO IN LEFT EARBUD OR EARBUDS ARE DISCONNECTED
FROM EACH OTHER (MANUAL RESET)
Bluetooth
Settings
JLab JBuds Air
i
Enter your Bluetooth device settings
and forget the JBuds Air.
Take both earbuds out of the charging
case and keep them within 2 inches
from each other. Wait for Left earbud to
turn solid white and Right to blink
blue/white. You are now ready to pair
to your Bluetooth device.
2
3
4
1
Open the charging case door and leave both
earbuds inside. Starting with ONE earbud,
quickly press the button 4x times. Light
will blink blue 4x times then turn solid blue.
Leave the earbuds in the charging case.
Repeat with the other earbud. Quickly
press the button 4x times. Light will blink
blue 4x times then turn solid blue.
Bluetooth
Settings
JLab JBuds Air
BLUETOOTH DEVICE DOES NOT CONNECT / RECONNECT
Enter your Bluetooth device settings
and forget the JBuds Air.
2
On your device, turn OFF then
ON Bluetooth.
3
4
1
Bluetooth
Settings
Bluetooth
Settings
JLab JBuds Air
i
Take the earbuds out of the case.
Wait for Left to turn solid white
and Right blinking blue/white.
Select “JLab JBuds Air” in device
settings to reconnect.
CAUTIONS
• Avoid extreme heat, cold, and humidity.
• Avoid dropping or crushing the earbuds.
• Wax may build up in the earbud tips, lowering the sound quality.
Carefully remove the wax with a cotton swab or other small tool to improve the sound quality.
• If you experience discomfort or pain, try lowering the volume or discontinuing use temporarily.
• If you experience regular discomfort while using this product, discontinue use and consult your physician.
• We recommend you treat your earbuds as you would a nice pair of sunglasses and keep them in safe location when not in use.
JLABAUDIO.COM
• The Bluetooth connection is established from the right earbud. For the
most stable connection, keep the device near right hand side or in right
pocket.
• If you prefer to wear only one earbud, you must wear the right earbud
as this is the main earbud connected to Bluetooth.
• Choosing the correct ear tip makes a significant improvement in audio
quality due to proper seal for the driver. Try all ear tips for best results.
• Only ONE Bluetooth device can be connected at a time. Turn off
Bluetooth from unwanted devices and turn on Bluetooth from chosen
device to connect.
QUICK TIPS WARNING
Fully dry off the earbuds before
putting in the charging case to
avoid any damage to the case.
The earbuds are sweat/water
resistant but the case is not.
Shop products | Product alerts | Burn-in your headphones
JLab Audio + Burn-in Tool